|
Hi Everyone, A Video
Update is available,
40Mb.
Click Here.
Download my WebSite:
Click Here.
This is the comple
working Circuit for
the Magnet
Conditioning, only a
few minor
adjustments, like
voltage levels, need
to be done.
In my opinion I have
got the circuit
right and producing
the same effect as
what Floyd had in
the Sweet/Bearden
Video. I think it is
important to point
out that under the
Wave Tec Oscillator,
in the Sweet/Bearden
Video, Floyd had a
"Black Box". I
believe this box had
some hidden
Circuitry. I believe
the cable in Floyds
circuit that was
connected to the
Diode bridge came
from this box.
A picture of the
wave I am currently
getting is shown
below. This is taken
from a pickup coil
that has a closer
coupling to the AC
wave. 4 Volts per
division is not a
correct indication
of the power in this
circuit, it is just
an indication of the
wave.
Some information I
have gathered about
the
Sweet/Bearden Video
is documented in the
below table:
|
Time in the
video. |
Event in the
video. |
|
From about
9.40 to the
start of
9.41,
|
Floyd
switched off
the Black
Box under
the
Oscillator.
The Light
Bulb in the
conditioning
circuit goes
out, it can
be
determined
by the
reflection
on the
magnets.
|
|
At around
13.11 -
13.12 |
Floyd turns
the black
box back on,
Bedini says
"Now you got
both of them
locked". The
Light Bulb
comes back
on and
pulses like
it was at
the start of
the video
when Floyd
was
adjusting
the circuit
with the
Potentiometer. |
|
At 13.29... |
Bearden
was not sure
what or
where the
60Hz is
coming from
and asks
“The 60 Hz?
I am sorry
Sparky… The
60 Hz was…” |
|
At 17.30... |
The
flashing of
the light is
visible from
the
conditioning
circuit.
Indicating
Floyd
Discharging
the Cap into
the
Conditioning
coil. |
|
At 17.30... |
Sweet
explains
briefly the
working of
the
Excitation
coil and the
whole
Conditioning
Process.
Sweet
explains
explicitly
that this
needs to be
activated
with the
excitation
coil. Power
to drive the
excitation
coil is 1/3
Mill watt. |
|
At 18.45... |
Floyd
Explains
again the
complete
conditioning
process. He
explains
everything
right up
until the
end of the
video.
|
A very important
piece of information
I have had for a
while but partially
over looked is
a Letter from Mr
Sweet to John
Morrison with some
wave forms that I
believe to be
relevant to this
letter.
Click Here for the
Letter.
Click Here for the
Wave Forms.
The coils in the
conditioning circuit
are constructed as
follows:
Inside Cylinder: One
coil of 1.5mm wire
with a total of 116
turns, two layers on
a 160mm PVC
Cylinder.
Outside Cylinder:
Two coils, each 80
turns of 2mm wire.
The diameter of the
Cylinder is 250 mm.
The transformers are
out of UPS's for
computers. Both
UPS's are around
700Va and are the
older style of
UPS's. One was a
Powerware 5110 and
the other was an APC
UPS. The small step
down transformer was
out of an old
Kitchen Drink Maker
from memory.
After working nearly
every weekend for
the two and a bit
years on this
project I went to
Cairns for a
holiday, a well
deserved holiday. I
tried to make a
point of getting
time to visit Lutec
Australia to see the
Lutec 1000. I was
refused a visit and
they told me that
they only will let
Investors look at
the setup they have.
I was a bit sore
about that and had a
bit of a grudge.
Looking back on this
I want to make all
my information free
to everyone and
never hold any
secrets like some
others do.
The
good thing about my
holiday was I came
back fresh and with
new ideas. I also
read the book
"Secrets of Cold War
Technology - by
Gerry Vassilatos"
This book is a
brilliant book and
Gerry has done some
very good research
here. A lot of
things clicked into
place for me after
reading this book.
Well more coming
soon as always.
_____________________
To reach new
horizons...
|
