The above Circuits/Schematics/Layouts do however have errors
or inconsistencies:
- First is the PHD3050E, there does not appear to be a
part number in a TO262 package or a TO251 package. There
is however a:
PHD3055E.
- In this schematic, it does appear that this N Channel
Mosfett is pulling the ve+ rail marked +6.17v to
ground through R7, a 1 Ohm Resistor. I don't understand
this.
- Several connections or components are either not drawn
completely or are missing. See Circuit/Layout Issues below.
- The Coils don't appear to be drawn correctly or connected
correctly. Specifically X0 - X3, its currently DC (Always
on).
See the possible theory.
In my opinion this device is real and not a Hoax as some
have stated. I don't believe unless there is an elaborate see
through feed wire to this device, that it could operate in a
Microwave oven and still power the White LED's as it does in
the video.
Circuit/Layout Issues:
- Resistor R1 is missing from the RV1 to ground.
- U2 appears to be a HEX Inverter, there are Signal Diodes
and Resistors missing from each flashing LED.
- The Terminal X0 is missing.
- R7 is not connected to the ve+ rail or any other rail.
- We have a Diode and a 0.22 Ohm resistor missing from
the board and not shown on the PCB that is drawn in the
Schematic.
- Values of some components are missing. Some values are
not significant as Flashing Led's can be determined later
on by (4RC) for the time constant. Duty cycle is determined
by the Diode Resistor Combination.
- Coil Inductance is not given. Pot Core permeability
also is an important value to know.
- The operation of R7 to U3 and switching to Ground is
important to be able to understand. As it stands the way
it is connected and drawn does appear to be correct but
it does not make sense to switch to ground the rail one
is trying to charge.
EDIT:
For more information on my below description:
Click
Here
I believe I have made some progress on this Device. Coils
and operation of them could well be related to our long standing
works.
If the phasing and winding directions are correct, the LED's
on L1 and L3 will light and your Input power will drop slightly.
More information may be gleamed in a document by Paul Raymond
Jensen:
Click Here
Update 17-04-14
To reiterate on my previous discoveries I have discovered
what I believe may be an answer to this problem. In the following
schematic and picture I show my coils working as they should.
This said, I have found an advantage to the three coiler shown
above, better results can be achieved.
How to do it!
1: Coils must be 2 separate
distinct coils as is shown in the Schematic.
2: Coils must be Wired and orientated to Buck - Cancel the Magnetic
Field but Electric Field does Add. Just like Floyd Sweet said!
3: I suggest low Duty Cycle, 8% or so, at low frequency (20
- 100 Hz) just to test initially.
4: Start with low voltage on the input, slowly turn it up.
Once you're there you will see what I mean.
You will get:
1: Two Output pulses for one Input pulse.
2: Output is NOT affected by Input, Lenz's Law doesn't apply
from input to output! (May need a little fine tuning to get
the best result)
3: A small amount of Energy is needed to keep this effect going,
Power input is very small.
Where:
Red Trace is the Output Voltage.
Yellow Trace is the input Current.
Conclusion:
I believe this device to be significant. If I am correct
in what I have researched thus far, I believe there to be two
key's to make this work.
- Understanding the Coil Configuration and operation.
- Understanding the Switching and Timing.
If RDSon is significant at U3 then this page would be a very
good read for many:
Click Here
The On Resistances, in the prior link, are very low and many
of the Mosfett's are designed for high speed switching also.
This device intrigues me! I think the Magic happens in the
Coils but there could also be a switching component here also.
I have built this device on a Breadboard but as yet I have been
unsuccessful in my initial replication attempt. Its a relatively
simple Circuit except for the few small issues I have with U3
and the Coil Layout.
Related Document's:
Very Possibly Related to the operation:
Click Here
MELNICHENKO, Andrei - Russian Patent (RU 2009113271):
Click Here
The Big Brother of the above version showing up to 105
Watts of real Power:
Click Here
Translation of Notes: (m-3-1) (Math may not be correct,
this is my translation from original)
Click Here
*** I have shown in this
video how the Coils L2 and L3 shown above can interact
together with L1 *** :
Click Here !!!
Theory and Applications of the MC34063 and A78S40 -
Perhaps a Key Document in understanding the Circuits
above: Click Here
Credits:
Thanks to
RealStrannik.ru
Thanks to Atom for posting this information.
Thanks to my very good friend Gerry for putting me
onto this device.
Warning:
Since my early experiments back in 2010/11, on the A Vector
Potential, Coil Winding Directions and Connections, I have had
nothing but negative responses from "educated" people, on Coils
and Winding and how to connect them and what they do together
and how they can and cant interact together. If you're an "educated"
person, then I highly discourage you from experimenting on these
experiments as you will have failed before you had even begun.
However, If you want to learn and work slightly out of the
box then these very simple and inexpensive experiments are where
you should work first. What I am doing, is Richard Feynman's
Science! Not magic!
An "educated" man once wrote:
I wonder how stupid Charles would feel if he were alive today!!
All I can say, is, the arrogance of the "educated" is the
greatest weapon in the suppression of Energy Machines. If you
can see it, and you can not prove it to be a fraud, then it
must be real!
|
